TOYOTA / LEXUS key programmer with key emulator function 2008-2017

TOYOTA / LEXUS key programmer with key emulator function 2008-2017, TOYOTA / LEXUS key programmer with key emulator function

Supported models:

Cars with the KEYLESS-GO system, produced from 2008 to 2017, Car key programmer for sale online, Buy Car key programmer online, Where to buy car key programmer online.

Operating principle:

The device receives data from the SMART module and emulates a key card to check the system performance with the following types of transponders 94 / D4 / 98/88 / A8 / A9. The device also allows you to add a new key.

Device appearance:

After connecting the device to OBD, you will see a menu with available functions.

Device control:

Use the UP and DOWN buttons to select the required action.

Confirm the action with the ENTER button or mark with the CANCEL button.

Description of functions:

CHECK – testing the function of disarming via the CAN bus.

CONNECTION – testing the engine start function. ADD – the function of adding an additional key. Previously recorded keys are not deleted.

3.0 – current version of the program, Programador clave para Dacia Sandero en venta, Se vende programador de llaves para SEAT Ibiza, Programador clave para Peugeot en venta, Programador clave para Citroën en venta, Se vende programador clave para Kia Sportage.

Equipment

Key Programmer, Programador de llaves LEXUS con función de emulador de llaves, 
OBD cable
NEEDLES cable for connection to CAN bus
If the SMART module is not supported, you will see the message “LEARNING …”, wait about 1-2 minutes while the device analyzes the received data. Subsequent connections to this SMART module will not teach, the device will work instantly.

CHECK (disarming test function) This function is needed for CAMRY, PRADO, AVENSIS.

Connect the diagnostic cable to the device
Connect the device to the OBD diagnostic socket at the driver’s feet
Press and release the START / STOP button or press and release the brake pedal to “wake up” the car electronics
In the device menu, select CHECK
The doors will be unlocked and you will see the message OK !!!
Then execute the CONNECT function

CONNECTION (engine start test function)

Connect the diagnostic cable to the device
Connect the device to the OBD diagnostic socket at the driver’s feet
Press and release the START / STOP button or press and release the brake pedal to “wake up” the car electronics
In the device menu, select CONNECTION
If you see a TRAINING … wait until the training is over, about 1-2 minutes
If you see RISE TO BUTTON – press and hold the brake pedal, touch the device to the START / STOP button, with the back cover as marked with an oval in Figure 2. The ANTENNA ((Y)) should blink
Press the START / STOP button and start the engine
Press the EXIT button on the device and disconnect the device from the diagnostic connector
ADD (additional key add function)

Connect the diagnostic cable to the device
Connect the device to the OBD diagnostic socket at the driver’s feet
Press and release the START / STOP button or press and release the brake pedal to “wake up” the car electronics
In the device menu, select ADD
If you see a TRAINING … wait until the training is over, about 1-2 minutes
If you see RISE TO BUTTON – press the brake pedal and place the device against the START / STOP button, with the back cover as marked with an oval in Figure 2. The ANTENNA ((Y)) should blink.
You will hear one beep, remove the device from the button and apply a programmable key to the START / STOP button, you will hear a beep confirming the programming of a new key.
Press the EXIT button on the device and disconnect the device from the diagnostic connector

Errors and solutions

In case of an error message (ERROR), check the diagnostic connector, make sure that the machine “woke up” and try again.

If during the operation of the CONNECTION function there are errors, it is possible that there is a key to this car in the car. Remove it or remove the battery from it.

If the ADD function is unable to add the key, the key may not be new or it may not be suitable for the vehicle. Erase the key using

Cars with A9 keys

RX (from 09.2015)

LC200 (since 2016)

LX570 (from 2016)

PRIUS (since 2016)

C-HR etc.

For some of these models, the Central Gateway module, when armed, blocks access via the diagnostic bus. There are alternative connections to the SMART unit to bypass the blockage. To connect to the CAN bus, use the NEEDLE cable, the OBD cable must be connected to the OBD connector of the car.
Instructions:

TKP-3_v3.0_rus